Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Tim Dreher

Joined on the:

Nov. 8, 2018

Score

260

Comment(s)

2

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

Recent Activity

Question(s) asked

3

Answered question(s)

1

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

18/09/2019

 Ford Tim Dreher (260Pts.)

0

2017 F150, remote starts ok, no heater or dash lights

I bought a Evo -Fort 3 programmed by the place where I bought. Very easy installation. But tried it for the first time this morning, it started fine (set up for lock-unlock -lock) and found that the heater does not come on , I set the heat and fan to max before I shut down the truck last night. When I got in the truck all dash lights are off even the tach doesn't register that it is running, only thing showing is a box on the display that says to insert the key and turn to run position. There is some air blowing out of the dash but no lights on the heater controls. I had set it for defroster, max heat and max air. Some guidance would be appreciated.
Login to reply View 1 answer(s)

24/11/2018

 Mazda Tim Dreher (260Pts.)

0

Cannot get past solid blue light when attempting the second pass after Dcrytor

I have started from fresh multiple times on a 2015 Mazda CX-5,I get through steps 1-12 ok , hook up to laptop, do the Dcryptor program, go back to vehicle hook up the module , data link first then other connectors, then disconnect data link , then all other connectors. Then start at step 1 again, get to the solid blue light but when trying the step 5 with the OEM remote again the blue light stays on solid no matter how many times I retry the steps, I have an EVO-MAZT1, and have done the evo all Master reset numerous times as well to get back to a fresh starting point, enabling this vehicles recommended options as instructed. I always get everything to work as per instructions but cannot past the second pass solid blue light. I tried downgrading the firmware as suggested by someone else that was having the same problem. This is a push to start vehicle. This is not the first Evo that I have installed but just happens to be the wife's.
Login to reply View 1 answer(s)

22/11/2018

 Mazda Neal Meeker (260Pts.)

1

too many decrypts for evo all

I was having troubles programming the Evo All using the one key programming guide. So, I switched and tried the 2 key programming guide. It worked, but I was not able to do a take over. So, I have been trying to get the single key programming to work. It never actually worked, so I switched back to the 1 key guide.... I didn't see until just now that it couldn't be programmed more than once with the same vehicle. So, attempting to program it both ways screwed me up? long story short - the decryptor told me I can't try any more for my vehicle. So, it needs to be reset from the server end? (it would be nice if your computer software told you what cars you had generated keys for already... then you could use them or delete them yourself.... - programmer's 2 cents)
Login to reply View 1 answer(s)

19/11/2018

 Mazda Tim Dreher (260Pts.)

0

EVO-MAZT1, Guide 62951, 2015 CX-5 step 16 then to 1-12 steps

I get as far as step 15 , install the Dcryptor, then step 16 says to first install the 4 pin data connector, then the other connectors, step 17 says to go back and repeat steps 1-12. Does this mean remove all the connectors that step 16 asked me to install before starting at step one again, or just disconnect the data connector and press and hold the program button. I am a little confused on how to repeat steps 1-12 again if step 16 asked me to install all the connectors and never asked me to remove them.
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue